Aksesuar Rehberi

QUICKSILVER SPORT GAUGE - BLACK FACE - MATTE BLACK BEZEL

All gauges have anti-fog lenses and orange backlighting. Large gauges fit 3-3/8" (85 mm) hole in dash. Small gauges fit 2-1/8" (52 mm) hole in dash. Tachometers require tachometer harness or ignition/choke assembly for connection. Will require AGI converter for digital engines. Speedometers include 25 ft. (7.6 m) of tubing. Fuel level gauges use 12V system and require 240 ohm sender. Trim gauges require sender, sold separately. Water pressure gauges include 25 ft. (7.6 m) of tubing and hardware. Cruiselog gauges include wiring. Volt Meters require tachometer harness or ignition/choke assembly

• TACHOMETER-6K

  Kılavuz s.419
  • 79 8M6020097

• TACHOMETER GAUGE-7K

  Kılavuz s.419
  • 79 8M6020098

• SPEEDOMETER-45MPH

  Kılavuz s.419
  • 79 8M6020099

• SPEEDOMETER-65MPH

  Kılavuz s.419
  • 79 8M6020100

• FUEL LEVEL GAUGE E-F

  Kılavuz s.419
  • 79 8M6020101

• POWER TRIM GAUGE

  Kılavuz s.419
  • 79 8M6020102

• WATER PRESSURE GAUGE 0-30

  Kılavuz s.419
  • 79 8M6020103

• CRUISELOG GAUGE

  Kılavuz s.420
  • 79 8M6020104

• VOLTMETER GAUGE 8-18V

  Kılavuz s.420
  • 79 8M6020105

• WATER TEMP C-H (120-240)

  Kılavuz s.420
  • 79 8M6020106

• WATER TEMP C-H (60-200)

  Kılavuz s.420
  • 79 8M6020107

• OIL PRESSURE GAUGE L-H

  Kılavuz s.420
  • 79 8M6020108

QUICKSILVER SPORT GAUGE - BLACK FACE - BRUSHED STAINLESS BEZEL

All gauges have anti-fog lenses and orange backlighting. Large gauges fit 3-3/8" (85 mm) hole in dash. Small gauges fit 2-1/8" (52 mm) hole in dash. Tachometers require tachometer harness or ignition/choke assembly connection. Will require AGI converter for digital engines. Speedometers include 25 ft. (7.6 m) of tubing. Fuel level gauges use 12V system and require 240 ohm sender. Trim gauges require sender, sold separately. Water pressure gauges include 25 ft. (7.6 m) of tubing and hardware. Cruiselog gauges include wiring. Volt Meters require tachometer harness or ignition/choke assembly conn

• TACHOMETER-6K

  Kılavuz s.420
  • 79 8M6020109

• TACHOMETER-7K

  Kılavuz s.420
  • 79 8M6020110

• SPEEDOMETER-45MPH

  Kılavuz s.420
  • 79 8M6020111

• SPEEDOMETER-65MPH

  Kılavuz s.421
  • 79 8M6020112

• FUEL LEVEL GAUGE E-F

  Kılavuz s.421
  • 79 8M6020113

• POWER TRIM GAUGE

  Kılavuz s.421
  • 79 8M6020114

• WATER PRESSURE GAUGE 0-30

  Kılavuz s.421
  • 79 8M6020115

• CRUISELOG GAUGE

  Kılavuz s.421
  • 79 8M6020116

• VOLTMETER GAUGE 8-18V

  Kılavuz s.421
  • 79 8M6020117

• WATER TEMP C-H (120-240)

  Kılavuz s.421
  • 79 8M6020118

• WATER TEMP C-H (60-200)

  Kılavuz s.421
  • 79 8M6020119

• OIL PRESSURE GAUGE L-H

  Kılavuz s.421
  • 79 8M6020120

QUICKSILVER CLASSIC GAUGE - BLACK FACE - CHROME BEZEL

All gauges have anti-fog lenses and orange backlighting. Large gauge fits 3-3/8" (85 mm) hole in dash. Small gauge fits 2-1/8" (52 mm) hole in dash. Tachometers require tachometer harness or ignition/choke assembly connection. Will require AGI converter for digital engines. Speedometers include 25 ft. (7.6 m) of tubing. Fuel level gauges use 12V system and require 240 ohm sender. Trim gauges require sender, sold separately. Water pressure gauges include 25 ft. (7.6 m) of tubing and hardware. Cruiselog gauges include wiring. Volt Meters require tachometer harness or ignition/choke assembly conn

• TACHOMETER-6K

  Kılavuz s.422
  • 79 8M6020085

• TACHOMETER-7K

  Kılavuz s.422
  • 79 8M6020086

• SPEEDOMETER-45MPH

  Kılavuz s.422
  • 79 8M6020087

• SPEEDOMETER-65MPH

  Kılavuz s.422
  • 79 8M6020088

• FUEL LEVEL GAUGE E-F

  Kılavuz s.422
  • 79 8M6020089

• POWER TRIM GAUGE

  Kılavuz s.422
  • 79 8M6020090

• WATER PRESSURE GAUGE 0-30

  Kılavuz s.422
  • 79 8M6020091

• CRUISELOG GAUGE

  Kılavuz s.422
  • 79 8M6020092

• VOLTMETER GAUGE 8-18V

  Kılavuz s.423
  • 79 8M6020093

• WATER TEMP C-H (120-240)

  Kılavuz s.423
  • 79 8M6020094

• WATER TEMP C-H (60-200)

  Kılavuz s.423
  • 79 8M6020095

• OIL PRESSURE GAUGE L-H

  Kılavuz s.423
  • 79 8M6020096

QUICKSILVER CLASSIC GAUGE - WHITE FACE - CHROME BEZEL

All gauges have anti-fog lenses and orange backlighting. Large gauges fit 3-3/8" (85 mm) hole in dash. Small gauges fit 2-1/8" (52 mm) hole in dash. Tachometers require tachometer harness or ignition/choke assembly connection. Will require AGI converter for digital engines. Speedometers include 25 ft. (7.6 m) of tubing. Fuel level gauges use 12V system and require 240 ohm sender. Trim gauges require sender, sold separately. Water pressure gauges include 25 ft. (7.6 m) of tubing and hardware. Cruiselog gauges include wiring. Volt Meters require tachometer harness or ignition/choke assembly conn

• TACHOMETER-6K

  Kılavuz s.423
  • 79 8M6020073

• TACHOMETER-7K

  Kılavuz s.423
  • 79 8M6020074

• SPEEDOMETER-45MPH

  Kılavuz s.423
  • 79 8M6020075

• SPEEDOMETER-65MPH

  Kılavuz s.424
  • 79 8M6020076

• FUEL LEVEL GAUGE E-F

  Kılavuz s.424
  • 79 8M6020077

• POWER TRIM GAUGE

  Kılavuz s.424
  • 79 8M6020078

• WATER PRESSURE GAUGE 0-30

  Kılavuz s.424
  • 79 8M6020079

• CRUISELOG GAUGE

  Kılavuz s.424
  • 79 8M6020080

• VOLTMETER GAUGE 8-18V

  Kılavuz s.424
  • 79 8M6020081

• WATER TEMP C-H (120-240)

  Kılavuz s.424
  • 79 8M6020082

• WATER TEMP C-H (60-200)

  Kılavuz s.424
  • 79 8M6020083

• OIL PRESSURE GAUGE L-H

  Kılavuz s.424
  • 79 8M6020084

ANALOG GAUGE INTERFACE - DIGITAL ENGINES

Converts digital signal to analog

• DTS ENGINE - ANALOG GAUGE HARNESS

  Kılavuz s.425
  • 84 8M01505393 ft. analog gauge harness specific for DTS engines that is more cost effective than the AGI (Analog Gauge Interface) solution. Compatible with DTS, Outboard, and V6/ V8 engines.
  • 84 8M009571615 ft. analog gauge harness specific for DTS engines that is more cost effective than the AGI (Analog Gauge Interface) solution. Compatible with DTS, Outboard, and V6/ V8 engines.

• EXTENSION HARNESS- 17 FT

  Kılavuz s.425
  • 84 8M0150477Analog gauge harness to 4pin 3ft and 17ft extension (20 ft). Enhanced voltage suppression. Compatible with DTS, Outboard, V6/V8 engines.

• DTS ENGINE - ANALOG GAUGE HARNESS

  Kılavuz s.425
  • 84 8M009582620 ft. analog gauge harness specific for DTS engines that is more cost effective than the AGI (Analog Gauge Interface) solution. Compatible with DTS, Outboard, and V6/ V8 engines.
  • 84 8M009582725 ft. analog gauge harness specific for DTS engines that is more cost effective than the AGI (Analog Gauge Interface) solution. Compatible with DTS, Outboard, and V6/ V8 engines.

• HARNESS EXTENSION- 27 FT

  Kılavuz s.425
  • 84 8M0150478Analog gauge harness to 4pin 3ft and 27ft extension (30ft). Enhanced voltage suppression. Compatible with DTS, Outboard, and V6/V8 engines.

• DTS ENGINE - ANALOG GAUGE HARNESS

  Kılavuz s.425
  • 84 8M009582830 ft. analog gauge harness specific for DTS engines that is more cost effective than the AGI (Analog Gauge Interface) solution. Compatible with DTS, Outboard, and V6/ V8 engines.

• ANALOG GAUGE INTERFACE KIT

  Kılavuz s.425
  • 892486K08Used on 14-pin engines to convert a digital sensor signal into analog for tachometer, oil pressure/oil level, water temperature, trim, and fuel level analog gauges. There is also a connection for SC100 link gauges. Enhanced voltage suppression. Used with a 10-pin junction box connection. For non-PCM09 ECUs - fits SmartCraft compatible 14-pin engines.
  • 8M0109742Used on 14-pin engines to convert a digital sensor signal into analog for tachometer, oil pressure/oil level, water temperature, trim, and fuel level analog gauges. There is also a connection for SC100 link gauges. No voltage suppression. Used with a 10-pin junction box connection. For PCM09 ECUs only - fits SmartCraft compatible 14-pin engines.

• ANALOG GAUGE INTERFACE (AGI) KIT

  Kılavuz s.425
  • 892486K07Includes AGI module assembly, harness and hardware. For installations using analog gauges instead of SmartCraft. Use with analog tachometer, coolant temp, oil pressure or level, trim and fuel level. Enhanced voltage suppression. Race MerCruiser or outboard engines in single or multiple engine installations plus MerCruiser 496Mag/Mag HO engines.

• ANALOG GAUGE INTERFACE (AGI) KIT

  Kılavuz s.426
  • 892486K04For installations using analog gauges instead of SmartCraft. Use with analog tachometer, coolant temp, oil temp, oil pressure or fuel pressure gauges. Enhanced voltage suppression. Race MerCruiser engines with the 14 pin Deutsch connector engine wiring harness. One AGI kit per engine required.

• ANALOG GAUGE INTERFACE MODULE

  Kılavuz s.426
  • 892486T04Replacement AGI Module: analog outputs for tach, fuel level, trim position, block temperature and oil pressure. For NON-PCM09 ECUs - Must have digital sensors on SmartCraft engine in order for these to be converted to analog outputs. CDS service tool used to enable Tach Link output (which can be either digital link data or analog trim).

• VESSEL ANALOG GAUGE INTERFACE (AGI) KIT

  Kılavuz s.426
  • 892486K05For installations using analog gauges instead of SmartCraft. Use with analog tab position (port & starboard), fuel level (two fuel tanks) and trim position gauges. Enhanced voltage suppression. Race MerCruiser engines with the 14 pin Deutsch connector engine wiring harness. One AGI kit per boat required.

• TROLL CONTROL WITH Y HARNESS- DASH MOUNTED- ANALOG

  Kılavuz s.426
  • 87 8M0083439Troll Control will allow you to have the same functions that you get from the SmartCraft digital gauges and adjust the speed of the boat. By pushing the button up or down, you can feather your speed every 10 RPM. Go from idle to 1000 RPM or anywhere in between (some engines can actually go lower than idle (75-115 4 stroke (Walleye), 135-200 HP Verado 4 cylinder and 3.0L Optimax). This kit will be used in analog gauge installations. RPM will reset to idle when more than 2-3% movement occurs at th

• CONVERSION KIT - SMARTCRAFT SENSORS

  Kılavuz s.426
  • 889250K01New kit that allows you to use SmartCraft gauges on these engines. Gen II (2007) 75 HP - 115 HP 4 stroke 1.7L engines.

• SMARTCRAFT PITOT SENSOR KIT

  Kılavuz s.426
  • 8M0090447Pitot sensor kit provides speed information for SmartCraft gauges. 2.1L F75-115 Four Stroke and 150 Four Stroke

MONITOR PANELS FOR DIESELS

• PRIMARY STATION MONITOR PANEL

  Kılavuz s.427
  • 861014Warning lights are provided for low oil pressure, excessive coolant temperature, insufficient alternator output, glow plug activation & check engine light. Fits 1997 and newer 2.8 ES & EI 165 and 4.2 ES & EI (250 & 230)

DEPTH SOUNDERS

• BEZEL 52 MM

  Kılavuz s.428
  • 8M0120346Chrome bezel. 2 inch (52 MM). Bezel is a snap fit that has a round shape. Priced individually, sold @ multiples of 10

SPEEDOMETER PICKUPS

• SPEEDOMETER PICKUP

  Kılavuz s.428
  • 77409A1Pickup and mounting screws only.

• SPEEDOMETER PICKUP KIT

  Kılavuz s.428
  • 77409B1For use with bulk pack speedometers. Includes pickup, misc. hardware and 20 ft. (6.1 m) of tubing. Priced & packaged in qty. of 24

• SPEEDOMETER PICKUP TUBING

  Kılavuz s.428
  • 32 549505353 ft. (16.15 m) tubing.

WATER PRESSURE PICK-UP KITS

• TUBING-BULK 100 FEET

  Kılavuz s.428
  • 32 859785100Bulk water pressure tubing, gray. 5/32 OD x 3/32 ID. 100 foot length.

• ANALOG WATER PRESSURE FITTING KIT

  Kılavuz s.428
  • 32 8M0088855Fitting kit allows installation of an analog water pressure gauge to the engine. 2.1L F75-115 Four Stroke

• WATER PRESSURE KIT

  Kılavuz s.428
  • 8M0059531Components needed for water pressure gauges. 150 FourStroke Engines

• ANALOG BLOCK WATER PRESSURE SENDER

  Kılavuz s.428
  • 8M0145165Optional kit to add analog block water pressure feature to a digital engine. Applicable to DTS 3.4L V6 and 4.6L V8 engines (mechanical engines have this sensor as standard).

• FITTING ASSEMBLY (90 DEGREE)

  Kılavuz s.429
  • 22 8M0022199Includes o-ring 896699, adapter fitting 896094 and 90 degree elbow fitting 891533. Mercury 350 SCI 1B716557 thru 2B143542

• FITTING (90 DEGREE)

  Kılavuz s.429
  • 22 89153390 degree fitting used on pressure sensor kit. 2.5XS 2.5L DFI 0T997974 thru 1E000796

WATER TEMPERATURE SENDERS

Water temperature senders used for operation of a temperature gauge.

• WATER TEMPERATURE SENDER

  Kılavuz s.429
  • 13536A13A two wire temperature sender for use on V-6 outboard product. Furnished standard on engine powerhead, the fiche card specific to the application should be used to verify correct use.

• WATER TEMPERATURE SENDER

  Kılavuz s.429
  • 13536A14A four wire temperature sender for use on V-6 outboard product. Furnished standard on engine powerhead, the fiche card specific to the application should be used to verify correct use.

• WATER TEMPERATURE SENDER

  Kılavuz s.429
  • 806490T3/8 in. x 18 NPT threads, used for temperature gauge. Fits MCM/MIE engines

• WATER TEMPERATURE SENDER

  Kılavuz s.429
  • 97258A11/2 in. x 14 NPT threads, used for temperature gauge. Fits MCM/MIE engines

• COOLANT TEMPERATURE SENDER

  Kılavuz s.430
  • 805218TUsed for temperature gauge. Fits MCM/MIE EFI models

OIL PRESSURE SENDERS

• OIL PRESSURE SENDER

  Kılavuz s.430
  • 8M0068784For use with 80 PSI electric oil pressure gauge. Fits all MerCruiser engines with the thread-on terminal

• OIL PRESSURE SENDER KIT

  Kılavuz s.430
  • 8M0068785Includes sender and harness used with oil pressure gauges and 21 ft. (6.4 m) of wire. Fits Mercury/Mariner 25/30/40/45/50/60 (4-stroke).

• OIL PRESSURE SENDER

  Kılavuz s.430
  • 8M0068784For use with 80 PSI electric oil pressure gauge. Fits all MerCruiser engines with the thread-on terminal

POWER TRIM SENDERS

• POWER TRIM SENDER

  Kılavuz s.430
  • 805320A03Includes trim limit switch also. Fits MC-I, R, MR, Alpha One, Gen II, Bravo drives.

• POWER TRIM SENDER

  Kılavuz s.430
  • 805130A6For dual station applications. Fits MCM I/R/MR/Alpha One/Gen II/Bravo One & Two drives.

• POWER TRIM SENDER

  Kılavuz s.430
  • 805130A8For dual station applications. Fits MCM TR & TRS drives.

• POWER TRIM SENDER CONVERSION KIT

  Kılavuz s.430
  • 805134A3Converts single station sender to a dual station sender. Fits MCM Alpha One/Gen II/Bravo One & Two drives.

• ANALOG TRIM SENDER (PORT MOUNT)

  Kılavuz s.431
  • 8M0098273Port mount analog trim sender (black color) 40-60 Family 2, 75-115 EFI and Optimax (not digital Optimax) - Port mount only

• ANALOG TRIM SENDER (STARBOARD MOUNT)

  Kılavuz s.431
  • 8M0098264Starboard mount analog trim sender (natural color) 40-60 Family 2, 75-115 EFI and Optimax - Starboard mount only

• POWER TRIM SENDER

  Kılavuz s.431
  • 822573A12Port mounted. Contains 6-32 threaded mounting screws. Fits various in-line outboards. See application chart for specific engine models.

• POWER TRIM SENDER

  Kılavuz s.431
  • 859187A1Port mounted. Fits all SmartCraft compatible engines.

• POWER TRIM SENDER

  Kılavuz s.431
  • 896688001Digital Trim Sender See Electronic Parts Catalog for all applications

• POWER TRIM SENDER

  Kılavuz s.431
  • 891777A01Starboard Mounted. Required for digital gauge applications. Fits SmartCraft compatible engines.

• TRIM SENSOR CONVERTER KIT

  Kılavuz s.431
  • 8M0059529This kit will allow you to convert the signal from the digital sensor to an analog signal. It will allow you to drive an analog gauge for trim only without changing the sensor to an analog sensor. This kit will connect directly to the harness inside the engine cowl. F150 EFI FourStroke outboard engine only

• TRIM ANALOG TO DIGITAL AND LIMIT KIT

  Kılavuz s.431
  • 8M0118725This kit allows the conversion of the trim signal from the analog sender to a digital output for SmartCraft gauge applications. The kit also has an additional feature that allows the max tilt up position to be set to avoid interference when tilting the engine completely up. 2.1L F75-115 Four Stroke

SERVICE MONITORS

Digital tach and hourmeter. Features LCD display and re-settable hourmeter.

• SERVICE MONITOR

  Kılavuz s.434
  • 79 8M0050399Fits most Outboards and gasoline MCM/MIE engines. Will not work with diesel products, Verado outboards or the F75-115 FourStroke outboard 1B366823-2B094955. Replaces old versions with a universal product. Quicksilver Branded, Clamshell Package Point of Sale Packaged.

MECHANICAL TRIM POSITION INDICATORS - 1 POINTER

Cables not included with indicator kits. Order F5H208/_ cables or 64-820676A_ cables to proper length. Trim position indicator and bezel selection chart available within the Instrument section.

• TRIM POSITION INDICATOR

  Kılavuz s.434
  • 848445A61 pointer. Top cable entry. White faceplate and bezel. Fits single sterndrive.

MECHANICAL TRIM POSITION INDICATOR ACTUATOR KITS

• ACTUATOR KIT

  Kılavuz s.434
  • 846063A1Single Fits MCM Alpha - V SSM sterndrives

• CABLE GRIP KIT

  Kılavuz s.434
  • 846066A1Angled stainless steel through-transom fitting for trim position (cable not included).

• MECHANICAL TRIM ACTUATOR KIT M-SERIES TRANSOM

  Kılavuz s.434
  • 8M0124387Attaching kit for mechanical trim indication. To be used on M-Series transom when using mechanical indicators